MULTIPROP Post Shores are used as individual props and – in combination with MULTIPROP frames – as shoring towers or load towers under tables. Compared with tubular steel slab props, the aluminium MULTIPROP carries significantly higher loads whilst, at the same time, has a very low dead weight. With different frame sizes, square or rectangular shoring towers can be optimally adapted to suit individual construction site conditions. The frames also serve as platform beams and side protection for working levels.
High load-bearing capacity Fewer individual props per m² through permissible leg loads of up to 100 kN (according to type test)
Well thought-out details With self-cleaning thread, trendsetting Adjusting Nut and continuous adjustability
Time-saving length adjustment The integrated measuring tape on the inner tube shows the complete length of the prop
Practical wedge connection Multifunctional MRK Frame without any time-consuming bolted connections
Aluminium slab props with powder coating for transferring vertical loads particularly under slab formwork; as shoring tower with frames for transferring vertical loads over great heights
Leg loads up to 100 kN in accordance with the type test
Max. type-tested assembly height (shoring tower with MRK Frames): 14.40 m or 14.90 m (with Base Plate MP 50)
Building authority approved
Prop lengths: up to 1.20 m | 2.50 m | 3.50 m | 4.80 m | 6.25 m
Steel MRK Frames are available in the following sizes: 62.5 cm | 75 cm | 90 cm | 120 cm | 137.5 cm | 150 cm
Aluminium MRK Frames are available in the following sizes: 201.5 cm | 225 cm | 230 cm | 237 cm | 266 cm | 296 cm
Continuous thread for infifinite adjustment of the prop height without pegging
Adjustment range of up to 2.20 m (MP 480)
Provides 36 mm of adjustment with every turn of the nut
The securing hook prevents the inner tube from slipping out
Aluminium slab props – low weight with high load capacity
MULTIPROP slab props are made of aluminium which means they are very light, e.g. the MP 350 weighs only 19.40 kg. With its extension lengths from 1.95 – 3.50 m 90% of standard operations in building construction can be covered. Ingeniously designed details ensure a long service life.
The cleverly-designed profile made of aluminium alloy absorbs impacts elastically, e.g. when a prop falls over. Material selection and design are perfectly matched. The MULTIPROP thread is self-cleaning and the free-running collar does not jam, even when dirty.
MULTIPROP slab props MP 250, 350, 480 and 625 are officially approved by the Deutsches Institut für Bautechnik in Berlin (No. Z-8.312-824) and complies with DIN standard DIN EN16031.
Maximum load capacity
MP 120 (0.80 – 1.20 m)
MP 250 (1.45 – 2.50 m)
MP 350 (1.95 – 3.50 m)
MP 480 (2.60 – 4.80 m)
MP 625 (4.30 – 6.25 m)
Further technical details
Built-in measuring tape
Continuous, self-cleaning, quadruple thread
Nut with 4 robust lowering cams
Possibility of using tie rod
Outer tube ECC powder coated
Profile is solid and elastic = very robust
Anti-pinch safety device integrated in the system
Wide range of accessories: Prop connector; frame MRK; tilting forkhead MKK and tilting base MKF
Efficient underneath tables or as shoring tower
Connected with MRK frames, the MULTIPROP slab props are used under tables or as shoring towers. Leg loads of up to 100 kN allow cost effective transfer of loads. The MULTIPROP frames facilitate optimal customization on the construction site (regardless whether a square or rectangular assembly grid). The MULTIPROP frame can be used as a platform beam and side protection when assembling a working scaffold.
The MULTIPROP profile allows quick and easy assembly with the frames. The same frame can be connected to either the outer or the inner tube without changing the prop spacing (system spacing). The wedge is just hammered home into the frame’s coupling. Special tools are not required. Towers can be pre-assembled flat on the ground
High Load bearing capacity up to 100 kN and low weight of all components
The PERI MULTIPROP Frames can be mounted both the outer and inner tube
Built-in measuring tape
The MULTIPROP frame can be used as a platform beam
Optimized adjustment to the building: High load utilization through different frame sizes (12 frame sizes)
The PERI MULTIPROP and HD 200 systems could be combined in an ideal way in order to safely transfer the high vertical loads despite the complicated geometry of the steel lattice girders. Based on the experience during this project, I can say that for me, PERI is a formwork supplier with the technical expertise and large delivery potential that can help us to master such difficult tasks.